Earrings from beads. Yellow flower

Good afternoon. If you love beads and love to make beautiful things, today I offer you to make these wonderful earrings. So, below I will give a hand-drawn diagram. There’s nothing complicated, I think everyone will understand.

Effectuation of flower petals

1. Pick up the middle of the thread 8 beads and insert the needle top to bottom (back) to the fifth bead (see pic.1).
Gain an additional bead and insert the needle top to bottom (back) on the third bead.

Earrings from beads. Yellow flower
Gain an additional bead and insert the needle top to bottom (back) to the first bead.
Tighten both ends of the thread. Consider the resulting “ladder”
Further netting is conducted from the middle of the petal to the right and to the left.

2. Dial on the needle an additional bead and insert the needle (bottom to top) first and (bottom) from the formed teeth, (lower full turn) Tighten the thread.
Dial on the needle an additional bead and insert the needle (from bottom to top) second (middle) of the formed teeth. Pull the thread.
Dial on the needle an additional bead and insert the needle (bottom to top) in the third of the formed teeth. Pull the thread.

3. Dial on the needle an additional two beads and insert the needle top to bottom (back) to the top (newly formed) prong (the top one full turn). Gaining additional bead needle and insert into the middle prong.
Dial on the needle an additional bead and enter the first prong.
Note:Don’t forget every time you tighten the thread.
Earrings from beads. Yellow flower
4. Doing the first empty the bottom turn. Dialing for more beads, insert the needle upward into the first (lower) tine.
Dial on the needle an additional bead and insert the needle (bottom to top) in the second of the formed teeth.
Dial on the needle an additional bead and insert the needle (bottom to top) in the third of the formed teeth. Each time not forget to pull the thread.

5. Dial on the needle an additional two beads and insert the needle top to bottom (back) to the top (newly formed) prong (the top one full turn).
Gaining additional bead needle and insert into the middle prong.
Each time not forget to pull the thread

6. Perform a second lower empty rotate. Dialing for more beads, insert the needle upward in the middle (newly formed) prong.
Gaining additional bead needle and enter at the top prong.
Firmly and gently fasten and cut thread end.
Half of the petal is ready.

7. Put the needle on the second (free) end of the filament and perform the second half of the petal (see paragraphs 2-6) the Thread is not pinned and not cut!
You got truncated at the bottom of the lobe with five teeth on the upper edge

8.Spend needle through the first tooth, and use an extra bead and navigate through the second clove. Pull the thread. Similarly, place the additional beads between all the upper teeth.
Withdrawing the needle from fifth cloves, conduct her over the edge down (consistently swiping through the beads) to the first (last) of three lower beads including.

9. Gain an additional bead and insert the needle in the middle bottom bead, and then a third. Pull the thread tight.
Dial the second additional bead and insert the needle in the middle bottom bead, and then the first lower and the first additional (newly recruited).
Gaining additional third bead and insert the needle in the second (newly recruited) additional bead.
Spend several times the needle around the perimeter of the petal, pulling tight the thread.
Carefully clip the end of the thread.

To run products you will need the petals of three sizes.

Petals larger (10 and 12 Central beads) are performed similarly. In the first case (medium petal) you have 10 beads on the middle thread, and come back in the seventh, the second (large petal) – dial 12, and the return to nine. The bottom of the petal (all sizes) ends with three beads, the top – five teeth. Lobes at larger blank turns are performed as a lower and upper edge of the petal. It is due to run empty turns achieved the desired form of the petal.

The Assembly of the flower.

Consider made petals. All three variants of the petals the beads of the lower two ranks (one and two beads) are arranged vertically.
1. Select five petals. Check the accuracy of the fixing threads. The four petals of the ends of the threads cut. One end of the thread, the withdrawal of the lower beads (leaving the needle on the thread).
2. Spend several times the needle through the bottom beads (first row) five petals, joining them in the ring.
3. Carefully withdraw the needle in one of the petals to the bead of the second row, and a few times you take her consistently through the beads of the second row on all petals.
4. Going back to the beads of the first row as close as possible and collect them in the ring.
5. Gently and firmly fix the end of the thread.
The end of the thread cut. Them you’re going to sew your flower.
Options.
The petals can be made with beads of the same color. In this case, as parts of the flower clip is a beautiful bead.
Additional the bottom the beads can be in contrast to the petal colors. In this case, after the connection of the petals, they play the role of the parts of the flower.

The Assembly rose.

Rose bunk.
1.Perform two sets of petals medium (10 beads) and small (8 beads)
2. Build medium petals in a flower.
3. Small petals gather in the ring only through the bottom beads (first row). The thread formed of a bundle of spend through the hole in the center of the middle flower is made (p. 2) and fix.

Rose is three-tiered.
1. Perform three sets of petals – large (12 beads), medium (10 beads) and small (8 beads)
2. Build large petals in a flower.
3. Medium and small the petals are harvested in two rings only through the bottom beads (first row). Having a thread formed of a bundle of medium petals through the hole in the center of a large flower (p . 2). Spread your petals. Then having a thread formed of a bundle of small petals through the holes in the center of both the lower tiers of the rose.
4. Pull tight both threads and fix.

Options.
1.The petals of the middle and upper tier of the roses are different and the same size. The strands from both beams petals are held close to the hole in the bottom center of the flower and fixed.
2. The lower tier of the roses is performed in a five-petal flower. The number of petals of the middle and upper tiers is arbitrary.
Good luck to all.

Comments

comments